Roof Pitch Calculator will instantly estimate your roof slope from every possible angle.
You can calculate slope, area, rafters length and other dimensions. You can also convert roof pitch to Degrees (at the bottom).
1) Calculate Roof Slope Based On Rafters Length
Roof Span: | ft. | in. |
Roof Rise: | ft. | in. |
Roof Pitch = / 12″ |
How To Use Pitch Calculator
To estimate roof area, enter width and length (as shown in the measuring diagram below), and either Rise or Pitch – second value will auto-calculate. Click calculate. The results will pop up below the calculate button, and will include: Rafter Length, Total Size / Area, and Pitch.
Using the diagram below, measure your roof from the ground, and enter building dimensions into the calculator #2 above. Enter the span (also known as gable side width), and the rise above the base line.
To calculate your pitch and size, measure your roof and plug in your measurements in accordance with the diagram below. Enter EITHER Roof Rise or Roof Pitch.
2) Pitch to Angle (Degrees) Calculator
Enter pitch in the first box – calculation is automatic.
Enter Roof Pitch: | / 12″ |
Results: | degrees angle |
How To Measure Roof Rise
If you do not know the rise, and do not have a ladder or cannot access your roof in order to measure it, you can accurately estimate the rise by measuring 3 spans of siding.Typical vinyl siding has 4″ exposure, so 3 spans would be equal to 12″ or 1 foot. Calculate the number of spans from the base line to the peak. Since most homes have a Rake wood, which is usually 6-8″ wide, you can add that width to the rise.
Example: If you have 19 spans of siding at 4″ exposure (width) of each span, and a 6″ rake board, the rise would be:
[6″ + (19 * 4″)] / 3 = 6′ 10″ roof rise.
Converting pitch (US / Canadian slope measuring method) to degrees (European slope measuring method) can be useful in figuring out the roof geometry, or for European contractors who are not accustomed to th eUS system. See Table below:
Additional Resources
To learn additional information about why roof pitch is important and different methods of calculating it, refer to our comprehensive Roof Pitch Guide.
To get roof rafters length and accurate replacement cost, use our Rafter Calculator.
If you need to to quickly estimate how much a new roof costs, use our Roof Installation Calculator
To estimate pricing for 3-tab and architectural shingles, use our Asphalt Shingles Calculator
Cost per sq. ft.
Roof Size:
Roofing Material:
See costs in your area Start Here - Enter Your Zip Code
I've been a roofer for 13 years, and specialize in Metal Roofing and Flat Roofing.
Have a roofing question or issue? Ask me any roofing question!
Roofing Contractors - join our free Local Roofers directory to get more customers!
If my building is 28 feet in width and I take 5 feet pitch, what rafter length do I need?
Noel,
So if your gable end is 28′ wide, with 5 rise, your pitch is 4.285714285714286 … round up to 4.3 / 12
We actually have a tool for that – rafter length calculator. I recommend you try it. Here are the numbers I got from that tool:
You will (most likely) need a 16 feet rafter length, assuming you have overhangs that are LESS than 13″ (1 foot 1 inch) on each side.
If your overhangs are 1′ 2″ or more, up-to 5′ – you will need a 20′ rafter length. I’ve never seen overhangs wider than 3-4′ thought 🙂
Both 16′ and 20′ rafters are available in regular pine 2x wood from lumber yards and Home Depot / Lowe’s etc.
If you go over 20′, you will need LVL or engineered lumber, which is much more expensive. But in your case that is not necessary, because I don’t suppose you will have overhangs that over 5′.
Good luck
Hi I’m building a shed 24ft by 8ft and 7ft high, I’m using fiber cement roof slates but need my roof pitch has low has I can get it, can you please tell me how high I can go on the hight from sole plate to hight of roof, I hope this makes sense.
A novice
Dave
if the roof needs to have 2 degrees at least fall and roof has 4 metre lengths skillon roof, what is the angle pls
Cate, angle is 2 degrees 🙂
At 4 meters run, your rise should be 3.5 cm (at 2 degree angle) … if I did the math correctly 🙂
Hi,
I need to calculate a minimum 5 degree pitch over 3600 ml length. The height of the highest point is 2500 ml, and I want to calculate my post height.
Cheers,
Michael
I’ve work out over 12” a rise of 3/4 world that be 4 degrees
I found this very helpful.
If the slope of your roof is greater than 6° rising
to horizontal 12°, better opt for the roofing brackets or boards.
This is very helpful, thank you.
From what I know of angles and degrees 12/12 is 45 degrees. So 1/2 of that is 6/12 or 22.5 degrees.
PA,
If we use that logic, then 24 pitch roof should be 90 degrees, right (12*2 same as 45 degrees * 2)? But it’s not. It’s about 63.5 degrees. Like I said – it is not a straight line. Each step is smaller than the previous one. Look at last diagram:
1 pitch is 4 degrees.
2 pitch is 9.5 degrees – that’s a 5.5 degrees step.
3 pitch is is 14 degrees – that is a 4.5 degrees step.
from there it slowly declines or stays the same…
However, those are not exact numbers – it’s more like 14.04 degrees for a 3 pitch.
These roof pitches are treated as right triangle, and by applying the theory, the inverse tangent of 6/12 is actually 26.565 degree.
if 12/12 is 45°, why is not 6/12 = 22.5°?
also tool above says my pitch is “NaN/12”
Pa,
Quick answer – because it is not a straight line increase of 3.75 degrees, for each 1/12″. I will look into why you are getting “NaN”
The NaN issue happens when a user enters ” after the number in the input text box. These types of characters should not be allowed as input. Hope that helps.
Thanks Tim, I will look into it … i’m not big on JS … more of a roofer here 🙂